Winter Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: dumps65

EMC DES-1241 Dumps

Page: 1 / 10
Total 96 questions

Specialist - Platform Engineer PowerStore Exam Questions and Answers

Question 1

What is the last step when adding a drive to a Dell EMC PowerStore system?

Options:

A.

Verify the new drive is seen

B.

Add the drive to the pool

C.

Backup the keystore

D.

Zero the drive

Question 2

A Storage Administrator needs to add drives to a base enclosure of a Dell EMC PowerStore 7000T system. The system currently contains 10 750 GB NVMe SCM drives.

Which drive configuration maximizes the base enclosure capacity?

Options:

A.

11 15360 GB NVMe SSD drives in slots 10 - 20

B.

13 15360 GB NVMe SSD drives in slots 10 - 22

C.

11 750 GB NVMe SCM drives in slots 10 - 20

D.

13 750 GB NVMe SCM drives in slots 10 - 22

Question 3

While on-site installing a Dell EMC PowerStore T system, the node A embedded module management Ethernet port link LED is off. What does this indicate?

Options:

A.

Network connection is established

B.

No network connection is established

C.

Port speed is 1 GB/s

D.

Port speed is 10 GB/s

Question 4

Refer to the exhibit.

as

A Storage Administrator noticed a drive LED blinking blue. What does this indicate?

Options:

A.

Is faulted

B.

Access activity

C.

Power up

D.

Identification is on

Question 5

Which component can be replaced while the Dell EMC PowerStore is up and running?

Options:

A.

4-Port Mezz card

B.

SFP

C.

M.2 Device

D.

LCC

Question 6

During Dell EMC PowerStore startup, both appliance nodes have rebooted in service mode. What must be done first to avoid management software conflicts?

Options:

A.

Reboot node B

B.

Clear the boot mode

C.

Disable node B boot mode

D.

Return node A to normal mode

Question 7

What is the maximum number of base enclosures in a cluster when planning a Dell EMC PowerStore T installation?

Options:

A.

1

B.

2

C.

3

D.

4

Question 8

When connecting a PowerStore base enclosure to 2 expansion enclosures, match the base SAS ports in column A to their corresponding expansion LCC ports in column B.

as

Options:

Question 9

What is the default log collection schedule?

Options:

A.

Weekly

B.

As scheduled during install

C.

Hourly

D.

Daily

Question 10

What describes Dell EMC PowerStore X front-end cabling?

Options:

A.

Uses internal VMware virtual switching and does not require a management network

B.

Storage and management use the same LACP bonded cable connection

C.

Uses VLTi data switch interconnectivity to support vMotion networks

D.

Management and discovery use the same cables and connections as storage

Question 11

For what is the “svc_container_mgmt status CP” command used?

Options:

A.

Clears the Control Path audit log

B.

Resets the Data Path root access

C.

Checks the status of the Control Path

D.

Checks the status of the Data Path

Question 12

What is the protocol used for the storage network?

Options:

A.

FC

B.

NFS

C.

SMB

D.

iSCSI

Question 13

What does the output of the PSTCLI command “nas_server show” display from a Dell EMC PowerStore T?

Options:

A.

If NAS servers are present if they are either NFS or Licensed

B.

Memory utilization and thread count for NFS NAS servers

C.

If NAS servers are present and if they are either Started or Degraded

D.

SIDs of SMB NAS servers joined to the AD Domain

Question 14

Refer to the exhibit.

as

What type of cable is used for the ToR switch configuration shown for the S5248F-ON switches?

Options:

A.

10 GigE Cat 6 Ethernet RJ-45

B.

25 GigE Twinax

C.

100 GigE QSFP28

D.

10 GigE SFP optical cable

Page: 1 / 10
Total 96 questions