Exin CDCS Dumps

Perforated tiles should be located in front of equipment racks, aligned with cold aisles, to deliver supply air directly to server intakes. Best practice is one perforated tile per rack, adjusted based on airflow requirements and rack load.

Placing tiles at the back (A) disrupts airflow.

Spacing every 5th rack (B) provides insufficient cooling.

Placing near AC (D) causes uneven distribution and pressure loss.

Thus, option C is correct.

Electromagnetic fields are generated by current-carrying conductors. To minimize stray EMF, phase conductors should be physically close and balanced. A three-phase combined cable (all phase conductors and neutral in one sheath) ensures magnetic fields cancel each other due to phase opposition.

If phases are run separately (answer B), the separation increases loop area and magnetic field leakage. Single-phase cabling (A) is even worse because current does not balance across three phases. Bus bar trunking (C) provides physical support but often separates conductors, which may worsen EMF if not specifically shielded.

Therefore, the correct solution is three-phase combined cable (often XLPE-insulated). This design reduces EMF impact to within ANSI/TIA-942 and IEEE recommendations.

The correct formula for calculating Phase-to-Neutral Voltage in a three-phase power system is Phase-to-Neutral Voltage = Phase-to-Phase Voltage / 1.732. This formula applies to balanced three-phase systems, where 1.732 (or √3) represents the relationship between line-to-line and line-to-neutral voltages.

Detailed Explanation:

In three-phase systems, Phase-to-Phase Voltage is higher than Phase-to-Neutral Voltage by a factor of √3. Dividing the phase-to-phase voltage by 1.732 gives the phase-to-neutral voltage, which is critical for understanding power distribution in three-phase electrical systems commonly found in data centers.

EPI Data Center Specialist References:

EPI electrical training highlights the importance of knowing these calculations for designing and maintaining balanced power systems, which are essential for stable and efficient data center operations.

Raised floors must not be installed flush against perimeter walls. Buildings expand, contract, and shift due to thermal expansion (hygrothermal movement), structural settlement, and seismic activity. If the raised floor is rigidly connected to the walls, this movement transfers directly into the raised floor grid, causing buckling, cracking, or tile misalignment.

Industry standards (e.g., CISCA – Ceilings & Interior Systems Construction Association guidelines) require leaving a small perimeter gap (typically 1–2 cm) between raised floor tiles and walls. This gap is then sealed with flexible firestops or brush gaskets to control air leakage while preserving movement tolerance.

Therefore, the correct practice is to leave a separation space, making answer C correct. Options A and D restrict this requirement incorrectly, while B is factually wrong (sealing against the perimeter is not allowed).

LCC (Life Cycle Cost) is the metric that accounts for capital cost, operational energy, maintenance, and disposal/replacement. This holistic view is critical when evaluating cooling technologies like CRACs, CRAHs, chilled water, or free cooling systems.

HER (Heat Exchange Ratio) and COP (Coefficient of Performance) measure operational efficiency but not total lifecycle costs.

PUE measures overall data center efficiency but not specifically cooling CAPEX/OPEX.

Thus, LCC is the comprehensive metric that covers installation, operation, and disposal.

IEC 62040 defines UPS topologies:

VFD: Line-interactive; dependent on mains.

VI: Stabilizes voltage but not frequency.

VFI: Double-conversion online; fully isolates output from mains fluctuations.

Data centers require continuous, clean, and stable power. VFI is the only topology that protects against both voltage and frequency disturbances, meeting ANSI/TIA-942 Rated-3/4 requirements.

Thus, VFI is the ideal UPS class.

Commissioning occurs during the Implementation stage of the data center life cycle. This phase involves the final testing and verification of systems and equipment to ensure they meet design specifications and operational requirements before the data center goes live.

Detailed Explanation:

The Implement phase includes activities such as installation, configuration, and testing. Commissioning is a crucial step that validates the performance and reliability of all critical systems, including power, cooling, and network infrastructure, to ensure they operate as intended under various conditions. Proper commissioning helps identify and resolve any issues before the data center becomes fully operational.

EPI Data Center Specialist References:

EPI training emphasizes that commissioning is essential for verifying that the data center meets design and performance criteria, aligning with best practices in data center project management to minimize risks and ensure readiness for operation.

An End of Row (EoR) design minimizes the number of network switches, as multiple racks can share a single switch at the end of a row, reducing switch counts and simplifying management. This design centralizes network switching to fewer points, which reduces the complexity and number of switches required compared to a Top of Rack (ToR) design, where each rack typically has its own switch.

Detailed Explanation:

In EoR designs, each row has a single network switch that handles the connections for all racks within that row. This reduces the number of individual switches needed and centralizes network management, which is ideal for minimizing equipment and simplifying infrastructure in the data center.

EPI Data Center Specialist References:

EPI promotes the EoR design as a way to reduce switch counts and streamline management in data centers. This configuration allows for easier scaling and maintenance while maintaining efficient network connectivity.

An air intake temperature of 25 °C (77 °F) at the top of the rack is acceptable according to data center standards and guidelines, such as those from ASHRAE. This temperature falls within the recommended range for inlet temperatures, which is typically between 18°C (64°F) and 27°C (81°F).

Detailed Explanation:

ASHRAE standards provide guidelines on acceptable temperature ranges for air intake in data centers to balance cooling efficiency and equipment safety. A temperature of 25°C is within the recommended operational range, allowing data centers to optimize energy efficiency while maintaining safe conditions for IT equipment.

EPI Data Center Specialist References:

EPI guidelines align with ASHRAE recommendations for server intake temperatures, confirming that 25°C is within acceptable limits for most mission-critical equipment. This ensures the data center maintains an efficient and reliable environment.

NFPA 75 (IT equipment rooms) recommends pre-action sprinklers for data processing spaces to minimize accidental water discharge risk; wet-pipe is generally discouraged directly over IT hardware.

According to ASHRAE TC 9.9 Thermal Guidelines (2016), the recommended intake temperature range for Class A1 ICT equipment is 18–27 °C (64–81 °F). The allowable lower limit is 15 °C (59 °F). Setting supply to 4 °C (39 °F) falls far below these limits.

Operating at such low temperatures would:

Cause condensation risk when surfaces drop below dew point.

Create severe energy inefficiency, as chillers would run at extremely low setpoints.

Possibly damage hardware due to thermal shock.

Options A and B are misleading—system capability or dew point alone does not override ASHRAE guidelines. Option D is incorrect since 20 °C is a common design target, not a requirement.

Thus, supplying 4 °C is not acceptable.

With Halocarbon fire suppression systems, as the temperature increases, the amount of gas required for effective suppression decreases. This is because Halocarbon agents are stored as a liquid and discharge as a gas, expanding more at higher temperatures. As a result, less agent is needed at higher room temperatures to achieve the desired concentration for fire suppression.

Detailed Explanation:

Halocarbons rely on specific volumetric concentrations to suppress fires. Higher temperatures cause the agent to expand more rapidly, effectively filling the protected area with less agent needed to reach the required concentration. This is in contrast to some other gases, where temperature changes might not have the same effect on discharge quantities.

EPI Data Center Specialist References:

EPI data center training on fire suppression indicates that understanding the physical properties of agents like Halocarbons is key for correct system sizing. As the temperature rises, the gas expands more readily, thus requiring adjustments in the amount needed for effective coverage.

The Open Compute Project (OCP), initiated by Facebook in 2011, focuses on open designs for servers, storage, racks, and power systems. The goals are:

Reduce energy consumption by using efficient hardware.

Save materials by eliminating unnecessary components.

Lower costs by standardizing and sharing open designs.

Option B is wrong—OCP hardware can be adopted by enterprises as well. Option C is unrelated (OCP is hardware, not OS). Option D is broader cloud adoption, not OCP’s direct mission.

Thus, the primary focus is energy, material, and cost savings through open-source hardware.

In a wet pipe system, the piping is always filled with water under pressure. When a sprinkler head is triggered by heat, water is discharged immediately. This is the most common sprinkler system for general buildings.

Dry pipe: Pipes contain air or nitrogen; water enters only after valve activation.

Deluge: Pipes are empty, and all heads open simultaneously, releasing water everywhere.

Pre-action: Pipes are dry until detection and valve activation; reduces accidental discharge risk, recommended for IT rooms.

Since the definition describes immediate discharge from water-filled pipes, this is a wet pipe system.

The most effective EMF mitigation is to install shielding as close as possible to the source of radiation. By blocking or redirecting magnetic flux at the origin (the transformer room walls), the overall field propagation into adjacent areas is minimized. If shielding were placed at the computer room, the field would already have spread over the intervening space, requiring more material and higher cost.

Standards such as IEEE Std 299 (EMC Shielding Effectiveness) and IEC 61000 emphasize source-based mitigation. Additionally, ANSI/TIA-942 requires EMF shielding where magnetic flux exceeds recommended ICT thresholds (generally <5 mG for sensitive tape/disk storage).

Although 100 mG is often tolerated by modern equipment, legacy magnetic storage can be affected, so shielding is still prudent. Hence, the correct location is at the transformer room wall.

For an MCB (Miniature Circuit Breaker) in the PDU of an air-conditioning unit, a C-Curve is recommended. C-Curve breakers are suitable for circuits with moderate inrush currents, such as those experienced in air conditioning units. They provide protection against overloads while accommodating the inrush without nuisance tripping.

Detailed Explanation:

C-Curve breakers trip when currents exceed 5 to 10 times the rated current, making them ideal for devices like air conditioners that experience moderate inrush currents upon startup. This characteristic provides a balance between protection and resilience against startup surges, preventing unnecessary trips while safeguarding the circuit.

EPI Data Center Specialist References:

EPI guidance for data center electrical systems specifies that C-Curve breakers are appropriate for equipment with inrush characteristics similar to air conditioning units, as they help prevent operational interruptions caused by typical surges during equipment start-up.

Cooling airflow (CFM) can be calculated from:

Where P = IT load.

So approximately 500 CFM is required.

1,500 and 1,000 CFM are too high.

160 CFM is far too low.

Therefore, the correct answer is ~500 CFM.

Aerosol sprays release particulates and residues into the environment, which can contaminate sensitive ICT equipment. Such contamination accelerates corrosion, interferes with airflow, and increases particulate levels beyond ASHRAE recommended limits.

Proper cleaning should use HEPA-filtered vacuum systems or dry wipes, not aerosols. Even odor control aerosols are disallowed in critical rooms.

Therefore, aerosol cleaning solutions must never be used.

Relative Humidity (RH) is defined as the ratio of the actual water vapor content in the air to the maximum possible water vapor content at a given temperature. To calculate RH:

Dry bulb temperature (DBT): the ambient air temperature.

Wet bulb temperature (WBT): the temperature measured by a thermometer covered with a wet wick, influenced by evaporative cooling.

Using DBT and WBT, the humidity ratio and dew point can be determined with a psychrometric chart or Mollier diagram. From there, RH is calculated as:

A black text on a white background AI-generated content may be incorrect.

Options A and B are incomplete, while option C is an experimental method, not standard practice. The recognized method is option D.

ASHRAE recommends temperature and humidity be measured in the cold aisle, in front of racks, at approximately 1.5 m above the floor (average human working height) and 0.3–0.5 m from the rack face. This location captures the environmental conditions experienced at the IT equipment air intake, while still representing facility-level conditions (not single device-level).

Option A and C (at 50 mm intake/rear) are too close to individual servers and suited only for rack-level monitoring, not facility monitoring.

Option D (rear measurement) reflects exhaust air, not intake, and thus cannot be used to control environmental setpoints.

Maintaining measurement at standardized facility locations allows comparisons against ASHRAE’s recommended and allowable ranges (18–27 °C for Class A1 environments, 40–60% RH).

Battery sizing requires determining the real power demand of the UPS. With 30 kVA at 0.8 PF, the real load is 24 kW. To calculate required ampere-hours for 15 minutes of runtime, we need:

Where P = load, t = runtime, V = battery voltage, and η = UPS efficiency.

Without UPS efficiency, we cannot know actual DC load on the batteries. A UPS with 90% efficiency will require more battery capacity than one with 95%. None of the other listed parameters (PF, imbalance, charging current) are critical for runtime capacity calculation.

With infrequent/short outages, Standby (Emergency Standby Power, ESP) generators are appropriate; N+1 mitigates failure-to-start risk and supports concurrently maintainable designs.

When calculating Power Usage Effectiveness (PUE) in a data center that uses chilled water from an external source, like from a building owner, a weight factor for district chilled water must be applied. This is because PUE calculations aim to measure the energy efficiency of the data center’s own operations, and external utilities like district chilled water aren’t directly powered by the data center. A weight factor of 0.4 is typically used to account for the energy consumed to produce and deliver the chilled water, reflecting the indirect impact on the data center’s total energy consumption.

Detailed Explanation:

PUE is calculated as the ratio of the total facility energy to the IT equipment energy. If the cooling is provided by an external chilled water source, it’s necessary to adjust the calculations to accurately reflect the energy impact. By incorporating the 0.4 weight factor, data centers can calculate a more accurate PUE, aligning with standard methods and industry best practices.

EPI Data Center Specialist References:

EPI training on PUE highlights the importance of adjusting for external energy sources, such as district cooling, in the calculations. This ensures that PUE values remain accurate and comparable across different data centers, even when external utilities are used.

Best practice is to begin raised-floor installation at the center of the room, working outward. This minimizes alignment errors and ensures the tile grid is centered, which is critical for aisle containment and rack alignment.

Starting at the perimeter (A, B, D) causes cutting of tiles along both sides, misalignment with rack rows, and possible airflow inefficiencies. By starting at the center, tiles can be cut symmetrically around the edges, providing better aesthetics, balanced airflow, and structural stability.

Industry guidelines such as CISCA recommend this approach for raised floors in mission-critical spaces.

In seismic-prone areas, cables should be tightly secured to racks and cable trays to minimize movement during seismic activity. Properly securing the cables prevents them from being damaged due to excessive motion, which could lead to outages or damage to connected equipment.

Detailed Explanation:

Loose cables can be vulnerable to shaking or sudden jolts during an earthquake, increasing the risk of disconnection or damage. By tightly organizing and securing cables, you ensure they remain in place, even during significant movement, thereby maintaining connection integrity and reducing the risk of physical damage.

EPI Data Center Specialist References:

EPI training includes considerations for data centers in seismic zones, advising that cables be firmly anchored to support structures to reduce movement and mitigate potential damage during seismic events.

For a UPS system in a Rating-4 data center, the synchronization of output can indeed depend on the specific settings of the UPS. Generally, such systems allow for flexible configuration where the output can be synchronized to either power feed A or B, depending on which feed is preferred for stability or redundancy purposes.

Detailed Explanation:

In dual-feed setups, such as those in high-redundancy data centers, the UPS can be set to synchronize with either feed. This ensures that the UPS maintains continuity in case one feed becomes unstable or fails. The flexibility to choose synchronization to either feed enhances the resiliency and reliability of power supply, which is critical in Tier IV (Rating-4) facilities where uptime is paramount.

EPI Data Center Specialist References:

The EPI Data Center Specialist course underscores the importance of configurable UPS systems in Rating-4 data centers, where redundancy and continuous power are critical. By allowing synchronization to either feed, the UPS can maintain the highest level of reliability, which aligns with the rigorous standards expected in such environments.

Modern UPS systems can synchronize their output to an external reference, either from the rectifier input (Feed A) or from the bypass input (Feed B). Synchronization ensures seamless transfer between normal and bypass operation.

The configuration depends on user or vendor settings:

If synchronized to the bypass (Feed B), the UPS can quickly transfer to bypass during overload or failure.

If synchronized to the rectifier (Feed A), the UPS maintains stable output independent of bypass conditions.

ANSI/TIA-942 does not mandate which feed the UPS must synchronize to, only that redundancy be maintained across feeds in a Rating-4 design. Manufacturers typically allow the choice depending on operational preference.

A hypoxic-based fire suppression system works by reducing the oxygen level in a room to below what is necessary to sustain combustion. This makes it effective in fire prevention, but it is not suitable for continuous occupancy by personnel. Low oxygen levels can cause discomfort or even health risks for people spending extended periods in the space. Therefore, these systems are typically deployed in areas where continuous human occupancy is not required, such as storage rooms or data halls with limited personnel access.

Detailed Explanation:

Hypoxic fire suppression systems lower oxygen levels to around 15-16%, which is safe for short periods but not sustainable for continuous occupancy without risk to health. Data center environments where staff need to spend long periods monitoring and maintaining equipment would need alternative systems, like gas-based suppression that allows for safe evacuation rather than oxygen reduction.

EPI Data Center Specialist References:

The EPI Data Center Specialist curriculum emphasizes that fire suppression systems must be chosen based on occupancy requirements. Hypoxic systems are specifically noted as unsuitable for spaces requiring continuous human presence due to the low oxygen environment they create.

Blast protection should be considered if the data center or its location is a potential target or is near high-risk areas. Blast protection measures can protect both personnel and infrastructure from potential explosion impacts, which could be essential in areas with heightened security risks.

Detailed Explanation:

In areas where there may be risks of terrorist attacks or explosions due to nearby high-risk facilities, implementing blast protection measures helps safeguard the data center's infrastructure. These measures can include reinforced walls, blast-resistant windows, and secure entryways designed to withstand explosive forces.

EPI Data Center Specialist References:

While not specifically mandated by ANSI/TIA-942, EPI training advises considering local risk factors, including proximity to potential targets, when evaluating the need for blast protection. This approach is aligned with risk assessment and mitigation practices to ensure facility security.

The design and configuration of racks, particularly high-density and closed-circuit cooling racks, directly impact the fire suppression system design. Closed-circuit cooling racks, like blade-center racks, can affect airflow and potentially trap heat, influencing how fire suppression agents are distributed within the space. Therefore, it is essential to inform the fire suppression system supplier about the rack design to ensure effective coverage and proper agent distribution.

Detailed Explanation:

High-density racks can change how smoke and heat travel, which in turn affects fire detection and suppression. Closed racks with built-in cooling can isolate airflow, requiring adjustments in fire suppression design to ensure that suppression agents reach all necessary areas, including within enclosed spaces. The supplier may need to account for these factors to ensure proper protection coverage.

EPI Data Center Specialist References:

The EPI Data Center Specialist training underscores that fire suppression systems must be tailored to the specific environmental characteristics of the data center. The design of racks, particularly high-density configurations, should always be considered to ensure that suppression agents can effectively control a fire, even in contained rack spaces.

The diagram shows three UPS modules, each 100 kW, connected in parallel to support a 100 kW IT load. That means:

One module (100 kW) can support the load (N).

Two additional modules are installed as redundancy.

This equals N+2 redundancy.

2+N+1 and 2(N+1) imply dual active paths not shown.

N+N+N is not an industry term.

Thus, the correct redundancy level is N+2.

PUE (Power Usage Effectiveness) is the most widely used metric to evaluate the energy efficiency of data centers. Defined by The Green Grid and adopted in ISO/IEC 30134-2, PUE is the ratio of the total facility power to the ICT (IT load) power.

Formula:

Total Facility Power includes all electrical consumption: IT, cooling, lighting, power distribution losses, UPS inefficiency, etc.

ICT Equipment Power is only the load drawn by servers, storage, and networking gear.

An ideal PUE is 1.0, meaning all power is used by ICT equipment with no overhead. Typical enterprise values are 1.5–2.0, while hyperscale operators target <1.2.

Other options are incorrect:

B represents the inverse metric, known as DCiE (Data Center infrastructure Efficiency).

C and D are partial subsystem efficiency metrics, not the global PUE.

Hydrogen sulfide (H₂S) is a corrosive gas that readily reacts with metals, especially copper and silver found in circuit boards, connectors, and power supply components. Even at concentrations below human detection thresholds, H₂S can cause sulfidation corrosion leading to intermittent connections, failure of solder joints, and increased failure rates of electronic equipment.

ASHRAE Technical Committee 9.9 has documented multiple failures in data centers due to corrosive gases (notably sulfur-bearing compounds). Therefore, high humidity combined with H₂S presence accelerates this risk.

H₂S does not affect static flooring properties (B) or fire suppression agent chemistry (D). Option A is clearly incorrect as the risk is well-documented.

Halocarbon agents such as FM-200 (HFC-227ea) and Novec-1230 (FK-5-1-12) are both defined under NFPA 2001 and ISO 14520 as clean agents, but their required design concentrations and physical properties differ. When calculating agent quantity, the minimum extinguishing concentration (MEC) and safety factor (S) must be taken into account. The S-factor is specific to each agent and reflects differences in molecular weight, density, and flame suppression chemistry.

For Novec-1230, the required design concentration is generally lower than for FM-200 (around 4.5–6% vs. 7–9%), but the calculation formula is the same except for substituting the correct S-factor. Therefore, you cannot reuse the exact formula parameters from FM-200; you must change the S-factor and apply Novec-1230’s physical constants.

This ensures compliance with NFPA 2001 Annex C, which provides correction formulas for room volume, temperature, and specific agent type. Using the wrong S-factor could result in underfilling or overfilling, compromising fire safety or increasing cost unnecessarily.

Testing smoke sensors should be conducted according to the vendor specifications to ensure compliance with safety standards and accurate results. Vendors provide specific testing procedures to account for the sensor type, environment, and operational characteristics, ensuring that tests do not damage the equipment or provide false results.

Detailed Explanation:

Smoke sensors can vary by type and sensitivity, so following the vendor's recommended testing procedure ensures the sensors function correctly without risking sensor damage. Injecting smoke or using a self-test might be insufficient or could lead to inaccurate assessments if they do not align with the vendor's testing protocol.

EPI Data Center Specialist References:

EPI recommends adhering to manufacturer specifications for testing critical safety equipment, ensuring that tests reflect real-world conditions without compromising sensor integrity or reliability.

Design concentrations for halocarbons (e.g., FM-200/HFC-227ea, Novec 1230) increase with ambient temperature; higher temperature → higher minimum extinguishing concentration → more agent mass.