Netapp NS0-521 Dumps

In the scenario where a storage failover is performed on Node 1 in an HA pair, the path marked in the exhibit would becomeActive/Nonoptimized. After the failover, the LIFs from Node 1 that were activeand optimized will switch to Node 2. Paths that were previously optimized will become nonoptimized because they are now served through the partner node.

For more details, see:

NetApp Documentation on ALUA

To manage space automatically for a volume containing a LUN with fast-growing data, enabling automatic resizing on the volume is recommended. This feature allows the volume to grow dynamically as needed, accommodating the fluctuating data size without manual intervention. This helps in managing storage efficiently and ensures that the application has the required space.

For further details, refer to:

NetApp Documentation on Volume Management

NetApp Community Discussion on Automatic Resizing

In a NetApp ONTAP cluster using FCP, NVMe/FC, and NVMe/TCP, it is important to understand that NVMe/FC and FCP require different FC ports. This separation is necessary because the protocols, while both running over Fibre Channel, have different configurations and operational characteristics.

For more information, refer to:

NetApp Documentation on NVMe Configuration

NetApp Best Practices for SAN

To validate that the entire network path supports jumbo frames after an iSCSI implementation, you should perform a ping test from the host with fragmentation. This involves using the ping command with specific options to test jumbo frame support:

ping -M do -s 8972

In this command:

-M do ensures the packets are not fragmented.

-s 8972 sets the packet size to 8972 bytes (9000 bytes MTU minus 28 bytes for the ICMP header).

By confirming that the large packets are successfully transmitted without fragmentation, you can validate that the network path, including switches and adapters, supports jumbo frames.

For more details, you can check:

NetApp Documentation - iSCSI Configuration and Best Practices​ (NetApp)​​ (NetApp)​.

For configuring LUNs to share with ESXi hosts for datastores in an SVM created for FCP traffic, the following steps are necessary after creating the LUN:

Create an igroup with the ESXi hosts' WWPNs: This step involves defining an initiator group that includes the WWPNs of the ESXi hosts that need access to the LUN.

Map the LUNs to the igroup: This step assigns the LUN to the created igroup, allowing the ESXi hosts to access the LUN.

For further details, refer to:

NetApp Documentation on LUN and igroup Configuration

To migrate data from a LUN on an existing third-party SAN storage system to a new NetApp AFF A400 all-flash MetroCluster system, the supported methods include:

Foreign LUN Import in online mode: This method allows for data migration without significant downtime, enabling the system to continue serving data while the migration process is ongoing.

Foreign LUN Import in offline mode: This method involves taking the LUN offline during the migration process, which may be necessary in certain scenarios to ensure data integrity.

For more details, refer to:

NetApp Documentation on Foreign LUN Import

NetApp Community on LUN Import Methods

After deleting a LUN, if the space does not show as available, performing space reclamation is necessary. Space reclamation involves identifying and reclaiming unused space on the storage system, making it available for new data. This process ensures that the deleted LUN's space is properly freed up and reflected in the available storage capacity.

For more details, refer to:

NetApp Documentation on Space Reclamation

NetApp Community on Free Space Reclamation

When using Fibre Channel Protocol (FCP), the minimum number of FC switches needed to redundantly attach three ESXi hosts is 2. This setup ensures that each host has multiple paths to the storage, providing high availability and fault tolerance. Each ESXi host should be connected to both switches, allowing for continuous operation even if one switch fails.

For more information, refer to:

NetApp Documentation on FC Switch Configurations

NetApp Community Discussion on Redundant FC Setup

When planning to upgrade the UCS Server BIOS and Cisco NX-OS system running on the switches in a NetApp AFF ASA cluster environment, theInteroperability Matrix Tool (IMT)is the recommended resource to check compatibility with the new versions. The IMT provides detailed compatibility information for various hardware and software components, ensuring that the planned upgrades will not cause any interoperability issues.

For further details, refer to:

NetApp Interoperability Matrix Tool

To configure SnapMirror active sync across two data centers using FC (Fibre Channel), the required connectivity between NetApp ONTAP clusters is cluster peering. Cluster peering involves establishing a trust relationship between the clusters, allowing them to replicate data seamlessly. This setup ensures that data synchronization and disaster recovery processes are effective and reliable.

For more detailed information, you can check:

NetApp Documentation on SnapMirror and Cluster Peering

To verify compatibility in an iSCSI storage environment before a NetApp ONTAP software upgrade, the following tools are recommended:

Interoperability Matrix Tool (IMT): This tool helps verify the compatibility of different components, including network switches, hosts, and storage systems, ensuring that the planned upgrade will be supported.

Active IQ OneCollect: This tool collects comprehensive configuration and performance data from the storage environment, which can be used to assess the current setup and identify any compatibility issues before the upgrade.

For further details, refer to:

NetApp Interoperability Matrix Tool

Active IQ OneCollect Documentation

For a successful deployment of a switchless HA pair with two NetApp DS224C shelves in an already populated rack, it is crucial to verify:

Rack units: Ensure that there are enough rack units available to accommodate the new shelves and any associated equipment. Proper planning of space in the rack is essential for a neat and functional setup.

Power connections: Verify that there are sufficient and appropriately rated power connections available. Ensuring proper power distribution and redundancy is critical for the reliability and uptime of the storage system.

For more details, refer to:

NetApp Documentation on Rack Installation

NetApp Community Discussion on Power Connections

The recommended setting for using the NetApp ONTAP LUN fractional reserve is to set the space guarantee to "volume". This setting ensures that the required space for overwrites in the volume is reserved, preventing potential write failures when snapshot copies are created. This setup helps in maintaining the performance and reliability of the storage system by ensuring there is always enough space allocated for the LUN.

For further details, you can refer to:

NetApp Community Discussion on Fractional Reserve

NetApp Documentation on Space Management

Based on the output of the command lun igroup show -instance, which lists the protocol as fcp and the initiator as server1.netapp.com, the initiator type is WWPN (World Wide Port Name). In Fibre Channel Protocol (FCP) environments, WWPNs are used to uniquely identify Fibre Channel devices. This contrasts with IQNs used in iSCSI, and NQNs used in NVMe over Fabrics.

For more details, refer to:

NetApp Documentation on Initiators

For a small remote site with two ESXi servers requiring SAN storage and no switches, the recommended protocol isiSCSI. iSCSI allows for direct connectivity between the servers and the NetApp ONTAP storage system using standard Ethernet infrastructure, which is suitable for environments without Fibre Channel switches.

For more information, see:

NetApp iSCSI Configuration Guide

Selective LUN Mapping (SLM) is the feature that presents LUNs only within the HA pair. SLM allows administrators to control which LUNs are visible to which hosts, ensuring that LUNs are only accessible through the designated HA pair, thus improving security and manageability.

For more information, see:

NetApp Documentation on Selective LUN Mapping

NetApp Community on LUN Mapping

Implementing VLANs for NVMe/TCP configurations provides several benefits, two of which are increased resiliency and increased security:

Increased Resiliency: VLANs help segment the network traffic, reducing the risk of a single point of failure. By isolating NVMe/TCP traffic into specific VLANs, network issues can be contained within a VLAN, preventing them from affecting other parts of the network. This isolation ensures that disruptions are minimized and network resiliency is enhanced.

Increased Security: VLANs provide an added layer of security by segregating traffic. This segregation ensures that NVMe/TCP traffic is isolated from other types of traffic, reducing the risk of unauthorized access or data breaches. VLANs help in enforcing stricter access controls and monitoring, thereby increasing the overall security of the network.

For more information on the benefits of VLANs in NVMe/TCP configurations, you can refer to NetApp's technical resources:

Implementing and Configuring Modern SANs with NVMe-oF​ (NetApp)​.

SAN Configuration Best Practices​ (NetApp Community)​.

To configure an SVM to use NVMe/FC, the following steps are necessary:

Add the FC protocol: This step involves enabling the Fibre Channel protocol on the SVM, which is required to support NVMe over Fibre Channel.

Create an NVMe/FC LIF: Logical Interfaces (LIFs) must be created to handle NVMe traffic over the Fibre Channel network. These LIFs enable the NVMe namespace access to the host systems.

These steps ensure that the SVM is correctly set up to use NVMe/FC, allowing for efficient and high-performance access to NVMe storage.

For more information, refer to:

NetApp NVMe/FC Configuration

For automatic host discovery in a four-node NetApp AFF cluster using NVMe/TCP, the protocol used is mDNS (Multicast DNS). mDNS allows for the discovery of controllers and other networked devices without the need for a centralized DNS server, simplifying the setup process in environments that support NVMe over TCP.

For further information, refer to:

NetApp Documentation on NVMe/TCP

NetApp Community on Host Discovery